Not a member? Register Now
Sales & Support: 1.800.377.6329
DMC-12x0
PC/104 Optima Motion Controllers, 1-8 axes
Product Description
**For new applications, Galil recommends the new generation, Accelera series DMC-18x6 PCI controllers.**
The DMC-12x0 PC/104 bus motion controller is a member of the Optima Series, Galil's prior-generation, multi-axis motion controllers. Designed to fit in an embedded PC/104 system, the DMC-12x0 controller accommodates 1- through 8-axis formats and allows control of step or servo motors on any combination of axes. Any mode of motion can be programmed including linear and circular interpolation, contouring, electronic gearing and ecam. Like all Galil controllers, programming the DMC-12x0 is simplified with two-letter, intuitive commands and a full set of software tools such as WSDK for servo tuning and analysis.
Questions?
Call 1.800.377.6329 to speak with a Galil Application Engineer.
Product Features
- PC/104 card in 1 through 8 axis versions: DMC-12x0 where x=1,2,3,4,5,6,7,8 axes
- Accepts up to 12 MHz encoder frequencies for servos and outputs pulses up to 3 MHz for steppers
- PID compensation with velocity and acceleration feedforward, integration limits, notch filter and low-pass filter.
- Modes of motion include jogging, point-to-point positioning, contouring, linear and circular interpolation, electronic gearing and ECAM
- Multitasking for concurrent execution of up to eight application programs
- Non-volatile memory for application programs, variables and arrays
- Dual encoders, home input and forward and reverse limits accepted for every axis
- 8 Uncommitted inputs and 8 outputs for 1- through 4-axes models, 16 inputs and 16 outputs for 5- through 8-axis models
- Expansion for 64 I/O with optional DB-14064
- 8 uncomitted analog inputs
- High speed position latch and output compare
- DMA/2nd FIFO for instant access to status and parameters
- High-density shielded cables and optical isolation for noise immunity.
- Communication drivers for Windows
- Custom hardware and firmware options available
| Part Number | Description | 1pc/100pc |
| DMC-1210 | PC/104 1-axis | $1095 / $795 |
| DMC-1220 | PC/104 2-axis | $1495 / $875 |
| DMC-1230 | PC/104 3-axis | $1895 / $935 |
| DMC-1240 | PC/104 4-axis | $2195 / $995 |
| DMC-1250 | PC/104 5-axis | $2595 / $1345 |
| DMC-1260 | PC/104 6-axis | $2795 / $1425 |
| DMC-1270 | PC/104 7-axis | $2995 / $1525 |
| DMC-1280 | PC/104 8-axis | $3195 / $1595 |
| CABLE-100-1m | 100-pin cable; 1 meter | $175 / $135 |
| CABLE-100-2m | 100-pin cable; 2 meter | $190 / $145 |
| CABLE-100-4m | 100-pin cable; 4 meter | $210 / $160 |
| CABLE-36-1m | auxiliary encoder cable;1 meter | $90 / $75 |
| CABLE-36-3m | auxiliary encoder cable;3 meter | $110 / $90 |
| CABLE-80-1m | extended I/O cable; 1 meter | $125 / $95 |
| CABLE-80-4m | extended I/O cable; 4 meter | $150 / $105 |
| ICM-1900 | interconnect for 4 axis | $345 / $245 |
| ICM-1900-OPTO | ICM with isolated ouputs | $395 / $295 |
| ICM-2900-FL | ICM with flange mount | $295 / $195 |
| ICM-2900-OPTO-FL | ICM with opto & flange | $345 / $245 |
| ICM-2900 | interconnect for DMC-2xx0 | $295 / $195 |
| ICM-2900-OPTO | ICM with opto outputs | $345 / $245 |
| ICM-2908 | ICM for auxiliary encoders | $125 / $95 |
| CB-50-100-1200 | 50-pin to 100-pin (DMC-1200) | $75 / $50 |
| CB-20-25 | 20-pin to 25-pin (aux enc) | $15 / $15 |
| CB-36-25 | 36-pin to 25 pin (aux enc) | $50 / $45 |
| CABLE-26-25 | 26-pin to 25 pin (aux enc) | $15 / $15 |
| CB-50-80 | 50-pin to 80-pin (for DB-14064) | $75 / $50 |
| DB-12064 | 64 I/O expansion board for DMC-12x0 | $395 / $245 |
| -16 bit ADC for analog inputs | 16-bit analog-to-digital | $100 / $60 |
| AMP-19520 | ICM with two 500W servo drives | $595 / $395 |
| AMP-19540 | ICM with four 500W servo drives | $795 / $495 |
| -SR for AMP-195x0 | Shunt regulator option for AMP | $50 / $25 |
| WSDK | Servo Design Kit | $195 |
| ActiveX Toolkit | Active X toolkit | $595 |